Fluted column (by hand)

Setup sheet · 2026-11-19 23:11

Job

Machine
Custom, Carbide Motion, Router, Manual (M6)
Material
Hard maple rotary blank: round, 3.000 in diameter, 12.000 in long
XY zero
X at the left end of the blank, Y on the rotation axis centreline
Z zero
On the rotation axis, not the top of the blank
Rotary
Turned by hand. The program stops with the spindle off and the tool at safe Z before each new angle, and says which angle to turn the blank to. Angles count up as the top of the blank rolls toward −Y. Start with the blank at 0°. Raise the tool clear of the chuck and tailstock before starting.
Safe Z
0.500 in above the top face (2.000 in from the axis)
G-code units
Millimetres (G21)
Run time
About 7:04
Cutting extents
X 1.000 in to 11.000 in, Y -0.075 in to 0.075 in, Z 1.000 in to 1.600 in (work coordinates)

Tools

#ToolTypeDiameterCutting lengthStick-out
1T1 1/4" Upcut End MillEnd Mill0.250 in1.000 in1.500 in

Run order

#ToolpathToolAngleRPMFeedDepthTime
Load T1 1/4" Upcut End Mill and zero Z on the rotation axis before starting.
The program stops: turn the blank to 0° by hand, then press Cycle Start.
1Flutes @ 0°T10°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 45° by hand, then press Cycle Start.
2Flutes @ 45°T145°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 90° by hand, then press Cycle Start.
3Flutes @ 90°T190°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 135° by hand, then press Cycle Start.
4Flutes @ 135°T1135°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 180° by hand, then press Cycle Start.
5Flutes @ 180°T1180°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 225° by hand, then press Cycle Start.
6Flutes @ 225°T1225°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 270° by hand, then press Cycle Start.
7Flutes @ 270°T1270°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 315° by hand, then press Cycle Start.
8Flutes @ 315°T1315°10000 (dial)180 in/min0.125 in0:06
The program stops: turn the blank to 0° by hand, then press Cycle Start.
9Pin holes @ 0°T10°10000 (dial)40 in/min0.500 in0:08
The program stops: turn the blank to 90° by hand, then press Cycle Start.
10Pin holes @ 90°T190°10000 (dial)40 in/min0.500 in0:08
The program stops: turn the blank to 180° by hand, then press Cycle Start.
11Pin holes @ 180°T1180°10000 (dial)40 in/min0.500 in0:08
The program stops: turn the blank to 270° by hand, then press Cycle Start.
12Pin holes @ 270°T1270°10000 (dial)40 in/min0.500 in0:08

Checks