Long sign

Setup sheet · 2026-11-20 15:51 · Long Sign.tap

Job

Machine
PRO6060 (5 × 5 ft), Avid Mach4, VFD spindle, Manual (M6)
Material
Baltic birch plywood: 12.000 in × 96.000 in × 0.750 in
Tiles
2, fed through in Y: the material moves 59.000 in along Y between tiles. Each tile reaches 0.375 in past its tile lines. A page for each follows.
XY zero
Lower left of the tile, 12.000 in × 59.000 in: the same place on the machine for every tile
Z zero
Material top
Safe Z
0.500 in above the material
G-code units
Inches (G20)
Run time
About 14:24

Tools

#ToolTypeDiameterCutting lengthStick-out
1T1 1/4" Upcut End MillEnd Mill0.250 in1.000 in1.500 in
2T5 60° V-Bit 1/2"V-Bit 60°0.500 in0.433 in0.933 in

Run order

#ToolpathToolRPMFeedDepthTime
Tile 1 of 2: Set the XY zero at the material's lower-left corner and keep it for every tile. Run Long Sign - tile 1 of 2.tap.
Load T1 1/4" Upcut End Mill and zero Z (material top) before starting.
1Registration holesT11300050 in/min1.000 in0:28
Change to T5 60° V-Bit 1/2" and re-zero Z with the touch plate, then press Cycle Start.
2V-carve titleT51800080 in/min0.433 in2:57
Change to T1 1/4" Upcut End Mill and re-zero Z with the touch plate, then press Cycle Start.
3Drill hanging holesT11300050 in/min0.770 in0:04
4Cut out signT113000220 in/min0.770 in3:11
Tile 2 of 2: Move the material 59.000 in toward Y−; keep the XY zero. Run Long Sign - tile 2 of 2.tap.
Load T5 60° V-Bit 1/2" and zero Z (material top) before starting.
5V-carve titleT51800080 in/min0.433 in1:12
Change to T1 1/4" Upcut End Mill and re-zero Z with the touch plate, then press Cycle Start.
6Drill hanging holesT11300050 in/min0.770 in0:04
7Cut out signT113000220 in/min0.770 in2:06

Tile 1 of 2

File
Long Sign - tile 1 of 2.tap
Before it
Set the XY zero at the material's lower-left corner and keep it for every tile.
Drills
The spoilboard holes in front of the material at X 0.500 in, Y -0.375 in and X 11.500 in, Y -0.375 in, then the holes for tile 2's dowels at X 0.500 in, Y 58.625 in and X 11.500 in, Y 58.625 in, 1.000 in deep, before it cuts.
Cuts
Its share of the material, X 0.000 in to 12.000 in, Y 0.000 in to 59.000 in from the material's lower-left corner, and up to 0.375 in past its tile lines.
Cutting extents
X 0.500 in to 11.500 in, Y -0.375 in to 59.188 in, Z -1.000 in to 0.100 in (work coordinates)
Run time
About 6:41
#ToolpathToolTime
1Registration holesT1 1/4" Upcut End Mill0:28
2V-carve titleT5 60° V-Bit 1/2"2:57
3Drill hanging holesT1 1/4" Upcut End Mill0:04
4Cut out signT1 1/4" Upcut End Mill3:11

Tile 2 of 2

File
Long Sign - tile 2 of 2.tap
Before it
Move the material 59.000 in toward Y−; keep the XY zero.
Dowels
Line the holes tile 1 drilled up over the spoilboard holes and drop a 0.250 in dowel through each, at X 0.500 in, Y -0.375 in and X 11.500 in, Y -0.375 in. Clamp the material, then tap the dowels flush or pull them out before starting.
Cuts
Its share of the material, X 0.000 in to 12.000 in, Y 59.000 in to 96.000 in from the material's lower-left corner, and up to 0.375 in past its tile lines.
Cutting extents
X 0.875 in to 11.125 in, Y 0.188 in to 36.125 in, Z -0.770 in to 0.100 in (work coordinates)
Run time
About 3:21
#ToolpathToolTime
1V-carve titleT5 60° V-Bit 1/2"1:12
2Drill hanging holesT1 1/4" Upcut End Mill0:04
3Cut out signT1 1/4" Upcut End Mill2:06